Machine 7, high quality air-cooled  restoration and performance parts

     
 

Go Back   VW Forum - VZi, Europe's largest VW, community and sales > Volkszone TV > Tech Videos

Video-statistics
Categories in total: 9
Videos in total: 382
Top Contributors:
  1. JESUS (63)
  2. pugh dog (51)
  3. Brian Burrows (40)
  4. Greg McD (24)
  5. nefarious (23)
Categories
Search videos
Best rated videos (same category)
Classic VW Beetle Bug How to Sound Deadening Insulation Tip
Classic VW Beetle Bug How to Sound Deadening Insulation Tip
Vintage VW Training Film - Valve Adjustments Part 1
Vintage VW Training Film - Valve Adjustments Part 1
Related videos
Lowering the 69 VW Type 3 FRONT- Part 2 of 2
Lowering the 69 VW Type 3 FRONT- Part 2 of 2
How to set your timing type1 engine
How to set your timing type1 engine
Classic VW Beetle Bug Ghia Bus How to Time Set Engine Timing
Classic VW Beetle Bug Ghia Bus How to Time Set Engine Timing
Random videos
Classic VW Beetle Bug Documentary Film Assembly Line DVD
Classic VW Beetle Bug Documentary Film Assembly Line DVD
The Mk VII Volkswagen Golf GTI: Enough for you? - XCAR
The Mk VII Volkswagen Golf GTI: Enough for you? - XCAR
Jagerbug @ Bug Jam ~ Run # 1
Jagerbug @ Bug Jam ~ Run # 1
 
Paris Beetle Ragtop Install on a 1970 Beetle Part 8

Video-details
Title Paris Beetle Ragtop Install on a 1970 Beetle Part 8
Category Tech Videos
Rating
Date 03-10-2011, 12:40 PM
Description The headlining has been trimmed back at the sides and a strip of double sided tape put down to hold the headlining down. The side bars fit over this and get riveted down. If you got your measurements right the side bars should fit snuggly into the hole. Use the holes in the side rails to drill through and put the pop rivets in. Repeat for the other side. The front and rear bars are solid ali and well need clamping down, dont worry they do flex enough. Clamp them down and mark where they will need to be trimmed. I put 2 pop rivets in each end and one about 7cm away from these 2 and then evenly spaced out a few more between these. The reason fro this is that the bar is originally straight and will be contouring to the roof. The same is done on the front and afterwards you should have your complete frame in (Dont forget to pull the headlining under the front and rear bars.
by David.H
Hoster YouTube int.
Code to embed
Views 2,896
Comments 0

Comments
There aren't any comments to this video!

Video-Center of vBPoint (©)

All times are GMT +1. The time now is 04:16 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.

Disclaimer: For recreational purposes only, some assembly required. Any resemblance to real persons,
living or dead is purely intentional and the site admins are not responsible for direct, indirect,
incidental or consequential ridicule resulting from any defect or failure to perform. No animals
were harmed in the creation of this forum. Colours may fade over time. No other warranty expressed or implied.

volkszone.com

SupportingSupporting Brad's Cancer Foundation

 
 
© Volkszone • Terms and Conditions of use