Search Results for ‘flywheel’

Rebuilding a stock 1600cc engine. Spent time setting the end play to exactly 0.10mm and all within specifications. Torque nut each time and fitted correct shims. Then fitted flywheel oil seal and torque bout up to approx 300 ft lbs. Loctite on the thread. Came to finish off the rest of the...

1835cc engine parts for sale - all parts done less than 300 miles from new. 92mm Mahle Forged pistons/cylinders - £150 inc a 5th spare unused piston&cylinder. *** Sold pending payment *** :) 69mm forged counterweighted & 8-doweled crank. Spun a rod bearing so needs a re-grind on the big-ends...

Hi, I'm exploring the possibility of converting my Beetle to a custom electronic injection set-up. Obviously there were injection models made by the factory, so I'm thinking I may be able to incorporate some factory components. My question concerns engine-speed sensing in order to time the...

Hi, I'm after one of the torque meister tools for getting my flywheel off and engine, just before I do go ahead and buy a new one just wondering if anyone has one they would like to sell or even rent to me? I'll pay to rent of course! :) Chris

after a 109 tooth flywheel that will take a 200mm clutch, I believe these were fitted to some t2 and t3 and maybe 67 beetles. I also think there's "non o-ring" and "o-ring" versions ideally would like an o-ring version as its going on a late crank. it's for a beetle don't want to have to...

Hello, today the engine came out of my T3 bus to have the flywheel seal changed. When we took the flywheel off and cleaned it up we saw a few cracks in the wheel. How bad is this and is it safe to use? Some pics.

Anyone have one they don't need? £60 from Megabug so anything cheaper would be good.... :) These were fitted to 1.9 T25 water cooled 1983 on and all 2.1 injection T25 models. May also have been in the late 2L versions. Cheers. Dai. p.s. If anyone has a new clutch kit as well I'd be interested...

I have been researching, reading threads and books of how I go about upgrading my engine. I have a couple of questions which I was hoping someone might be able to help me with please... Is it possible with a 1300 engine to increase it to 1641, this I have researched so far will need 1600 heads...

As the title says. Type 1 200mm flywheels wanted. Watcha got? Regards...Schneeky:D

As i can't seem to change the title of my other posts i've started a new one. The bottom few i'm looking for cheap as chips prices :) wheel adapters - 4x130 to 5x205 (for my slightly pornographic empi 5s :tongue: ) merged header and single quiet pack (or seperately sourced) top door hinge...

hello to all at volkszone. I've been pulling my t4 engine apart to check for any problems, as its been sat for 3 years doing nothing, and have found 2 surface cracks in the flywheel. Is this a major problem, or is there a (cheaper) solution??? Also i salvaged my dash and dials from a rhd. Can i...

Up for sale from the engine project that never happened. All prices are including p&p! Genuine Twin Weber IDF 40's, Hex Bar Linkage kit, chrome rectangular air cleaners, velocity stacks, unmodified inlet Manifolds, supplied with: 2x 32mm and 2x 34mm Venturi's 4 x 52 Idle Jets ; 4 x 50 Idle Jets...

Hi folks, I've got to the stage of my engine build where I'm measuring up and setting the end float, i.e. long block basically complete. The problem I'm having is that there doesn't appear to be any noticeable end float, even when no shims are fitted. With the flywheel off, I get some...

I've been having engine problems with my 1600, so it's heads are stripped down. So I needed another engine to keep me going for a couple of weeks, and bought (as far as I can tell) a mid sixties 1500. The seller said he'd put the 12v (200mm clutch) flywheel from a 1600 (obviously 12v) on it...

Garage Clear Out - lots of nice gear Garage Clear out of excess stuff . Lots of nice quality buggy/beetle stuff. All prices plus postage and package + £3 paypal sur charge cheque ok to be cleared in my account before posting. Pictures here some bits little oily...

.

Just found out the clutch bolts on my old engine (180 mm clutch) don't fit the flywheel on new engine (200 mm clutch) does anyone know the correct size for them :confused:

130 teeth, good condition, £30 - not sure which Ø dimension to measure, but if you let me know I will get a ruler out!? :lol:

ok, so i have borrowed a flywheel locking tool, and a massive breaker bar off a friend, but does anybody have any tips for getting that blasted nut off? At the moment i am strugling to hold the crankcae in position, even though i have a piece of angle iron bolted to the flywheel, and then...